How to Replace the Arwibon 30 Controller?
The Arwibon 30 electric scooter is a reliable and efficient mode of transportation, known for its durability and performance. However, like any electronic device, its components may occasionally need replacement due to wear and tear or technical issues. One such component is the controller, which acts as the brain of the scooter, regulating power delivery to the motor and ensuring smooth operation. If your scooter is experiencing performance issues, such as erratic speed control, loss of power, or failure to start, it may be time to replace the controller. This guide will walk you through the process of replacing the Arwibon 30 controller, explain the reasons for replacement, and provide tips for maintaining your scooter.

Why Replace the Arwibon 30 Controller?
The controller is a critical component of your electric scooter, and there are several reasons why it might need replacement:
Performance Issues: If your scooter struggles to maintain speed, accelerates inconsistently, or fails to start, the controller may be faulty.
Physical Damage: Exposure to water, dust, or impact can damage the controller, leading to malfunctions.
Overheating: Prolonged use or excessive load can cause the controller to overheat, resulting in permanent damage.
Age and Wear: Over time, the controller’s internal components may degrade, reducing its efficiency and reliability.
Replacing the controller is a cost-effective way to restore your scooter’s performance and extend its lifespan.
Tools and Materials Needed
Before starting the replacement process, gather the following tools and materials:
A replacement controller compatible with the Arwibon 30 (check the specifications on Arwibon’s official website).
A Phillips-head screwdriver.
A clean, flat workspace.
Safety gloves and goggles (optional but recommended).
Step-by-Step Guide to Replacing the Arwibon 30 Controller
Follow these steps to safely and effectively replace your Arwibon 30 controller:
Step 1: Prepare Your Scooter
Turn off the scooter and ensure it is not connected to a power source.
Place the scooter on a flat, stable surface to prevent it from moving during the replacement process.
Step 2: Access the Controller
Locate the controller, which is typically housed inside the scooter’s deck near the battery compartment.
Remove the screws securing the deck cover using a Phillips-head screwdriver. Carefully lift the cover and set it aside.
Step 3: Disconnect the Old Controller
Identify the control line and power line connected to the battery. Gently unplug these cables from the controller.
Locate the three power lines connected to the controller. Disconnect them in order, ensuring you remember their positions for reinstallation.
Disconnect the signal line from the controller.
Finally, unplug the motor, instrument, and other control lines connected to the controller.
Step 4: Remove the Old Controller
Carefully remove the old controller from its housing. Be mindful of any screws or brackets that may be securing it in place.
Set the old controller aside for proper disposal or recycling.
Step 5: Install the New Controller
Take the new controller and ensure it matches the specifications of the original Arwibon 30 controller.
Position the new controller in the same location as the old one, securing it with screws or brackets if necessary.
Step 6: Reconnect the Cables
Connect the motor, instrument, and other control lines to the new controller, ensuring each cable is securely plugged in.
Reconnect the signal line to the new controller.
Connect the three power lines to the new controller, matching the colors of the wires to ensure proper functionality.
Reconnect the control line and power line to the battery.
Step 7: Reassemble the Scooter
Carefully place the deck cover back onto the scooter.
Reinsert and tighten the screws to secure the cover. Ensure the screws are evenly tightened to maintain a good seal.
Step 8: Test the Scooter
Turn on the scooter and check the instrument panel to ensure the new controller is functioning properly.
Take a short test ride to confirm that the scooter is operating smoothly and that the controller is delivering power as expected.
According to the video tutorial, ensure that the color of the control lines on the new controller matches the color of the corresponding lines from the scooter’s wiring. The lines must align correctly to prevent any electrical errors.
Replacing the controller in your Arwibon 30 electric scooter is a straightforward process that can significantly improve its performance and extend its lifespan. By following this step-by-step guide and maintaining your scooter properly, you can enjoy a smooth and reliable ride for years to come.